The xscreensaver program waits until the keyboard and mouse have been
idle for a period, and then runs a graphics demo chosen at random. It
turns off as soon as there is any mouse or keyboard activity.
This program can lock your terminal in order to prevent others from using it,
though its default mode of operation is merely to display pretty pictures on
your screen when it is not in use.
The benefit that this program has over the combination of the
xlock(1)
and
xautolock(1)
programs is the ease with which new graphics hacks can be installed. You
don't need to recompile (or even re-run) this program to add a new display
mode.
GETTING STARTED
For the impatient, try this:
xscreensaver &
xscreensaver-demo
The
xscreensaver-demo(1)
program should pop up a dialog box that lets you experiment with the
xscreensaver settings and graphics modes.
Note:
unlike
xlock(1),
xscreensaver has a client-server model: the xscreensaver program is a
daemon that runs in the background; it is controlled by the foreground
xscreensaver-demo(1)
and
xscreensaver-command(1)
programs.
CONFIGURATION
The easiest way to configure xscreensaver is to simply run the
xscreensaver-demo(1)
program, and change the settings through the GUI. The rest of this
manual page describes lower level ways of changing settings.
Options to xscreensaver are stored in one of two places: in
a .xscreensaver file in your home directory; or in the X resource
database. If the .xscreensaver file exists, it overrides any settings
in the resource database.
The syntax of the .xscreensaver file is similar to that of
the .Xdefaults file; for example, to set the timeout paramter
in the .xscreensaver file, you would write the following:
timeout: 5
whereas, in the .Xdefaults file, you would write
xscreensaver.timeout: 5
If you change a setting in the .xscreensaver file while xscreensaver
is already running, it will notice this, and reload the file. (The file will
be reloaded the next time the screen saver needs to take some action, such as
blanking or unblanking the screen, or picking a new graphics mode.)
If you change a setting in your X resource database, or if you want
xscreensaver to notice your changes immediately instead of the next time
it wakes up, then you will need to tell the running xscreensaver process
to re-initialize itself, like so:
xscreensaver-command -restart
Note that if you changed the .Xdefaults file, you might also need to run
xrdb(1):
xrdb < ~/.Xdefaults
If you want to set the system-wide defaults, then make your edits to
the xscreensaver app-defaults file, which should have been installed
when xscreensaver itself was installed. The app-defaults file will
usually be named /usr/lib/X11/app-defaults/XScreenSaver, but different
systems might keep it in a different place (for example,
/usr/openwin/lib/app-defaults/XScreenSaver on Solaris.)
When settings are changed in the Preferences dialog box (see above)
the current settings will be written to the .xscreensaver file.
(The .Xdefaults file and the app-defaults file will never be
written by xscreensaver itself.)
timeout (class Time)
The screensaver will activate (blank the screen) after the keyboard and
mouse have been idle for this many minutes. Default 10 minutes.
cycle (class Time)
After the screensaver has been running for this many minutes, the currently
running graphics-hack sub-process will be killed (with SIGTERM), and a
new one started. If this is 0, then the graphics hack will never be changed:
only one demo will run until the screensaver is deactivated by user activity.
Default 10 minutes.
lock (class Boolean)
Enable locking: before the screensaver will turn off, it will require you
to type the password of the logged-in user (really, the person who ran
xscreensaver), or the root password. (Note: this doesn't work if the
screensaver is launched by
xdm(1)
because it can't know the user-id of the logged-in user. See
the ``Using XDM(1)'' section, below.
lockTimeout (class Time)
If locking is enabled, this controls the length of the ``grace period''
between when the screensaver activates, and when the screen becomes locked.
For example, if this is 5, and -timeout is 10, then after 10 minutes,
the screen would blank. If there was user activity at 12 minutes, no password
would be required to un-blank the screen. But, if there was user activity
at 15 minutes or later (that is, -lock-timeout minutes after
activation) then a password would be required. The default is 0, meaning
that if locking is enabled, then a password will be required as soon as the
screen blanks.
passwdTimeout (class Time)
If the screen is locked, then this is how many seconds the password dialog box
should be left on the screen before giving up (default 30 seconds.) This
should not be too large: the X server is grabbed for the duration that the
password dialog box is up (for security purposes) and leaving the server
grabbed for too long can cause problems.
dpmsEnabled (class Boolean)
Whether power management is enabled.
dpmsStandby (class Time)
If power management is enabled, how long until the monitor goes solid black.
dpmsSuspend (class Time)
If power management is enabled, how long until the monitor goes into
power-saving mode.
dpmsOff (class Time)
If power management is enabled, how long until the monitor powers down
completely. Note that these settings will have no effect unless both
the X server and the display hardware support power management; not
all do. See the Power Management section, below, for more
information.
visualID (class VisualID)
Specify which X visual to use by default. (Note carefully that this resource
is called visualID, not merely visual; if you set the visual
resource instead, things will malfunction in obscure ways for obscure reasons.)
Legal values for the VisualID resource are:
default
Use the screen's default visual (the visual of the root window.)
This is the default.
best
Use the visual which supports the most colors. Note, however, that the
visual with the most colors might be a TrueColor visual, which does not
support colormap animation. Some programs have more interesting behavior
when run on PseudoColor visuals than on TrueColor.
mono
Use a monochrome visual, if there is one.
gray
Use a grayscale or staticgray visual, if there is one and it has more than
one plane (that is, it's not monochrome.)
color
Use the best of the color visuals, if there are any.
GL
Use the visual that is best for OpenGL programs. (OpenGL programs have
somewhat different requirements than other X programs.)
class
where class is one of StaticGray, StaticColor,
TrueColor, GrayScale, PseudoColor, or DirectColor.
Selects the deepest visual of the given class.
number
where number (decimal or hex) is interpreted as a visual id number,
as reported by the
xdpyinfo(1)
program; in this way you can have finer control over exactly which visual
gets used, for example, to select a shallower one than would otherwise
have been chosen.
Note that this option specifies only the default visual that will
be used: the visual used may be overridden on a program-by-program basis.
See the description of the programs resource, below.
installColormap (class Boolean)
Install a private colormap while the screensaver is active, so that the
graphics hacks can get as many colors as possible. This is the
default. (This only applies when the screen's default visual is being
used, since non-default visuals get their own colormaps automatically.)
This can also be overridden on a per-hack basis: see the discussion of
the default-n name in the section about the programs resource.
verbose (class Boolean)
Whether to print diagnostics. Default false.
timestamp (class Boolean)
Whether to print the time of day along with any other diagnostic messages.
Default false.
splash (class Boolean)
Whether to display a splash screen at startup. Default true.
splashDuration (class Time)
How long the splash screen should remain visible; default 5 seconds.
helpURL (class URL)
The splash screen has a Help button on it. When you press it, it will
display the web page indicated here in your web browser.
loadURL (class LoadURL)
This is the shell command used to load a URL into your web browser.
The default setting will load it into Netscape if it is already running,
otherwise, will launch a new Netscape looking at the helpURL.
demoCommand (class DemoCommand)
This is the shell command run when the Demo button on the splash window
is pressed. It defaults to xscreensaver-demo.
prefsCommand (class PrefsCommand)
This is the shell command run when the Prefs button on the splash window
is pressed. It defaults to xscreensaver-demo -prefs.
nice (class Nice)
The sub-processes created by xscreensaver will be ``niced'' to this
level, so that they are given lower priority than other processes on the
system, and don't increase the load unnecessarily. The default is 10.
(Higher numbers mean lower priority; see
nice(1)
for details.)
memoryLimit (class MemoryLimit)
The sub-processes created by xscreensaver will not be allowed to
allocate more than this much memory (more accurately, this is the maximum
size their address space may become.) If any sub-process tries to allocate
more than this,
malloc(3)
will fail, and the process will likely exit (or safely crash) rather than
going forth and hogging memory.
The assumption here is that if one of the screenhacks is trying to use
a lot of memory, then something has gone wrong, and it's better to kill
that program than to overload the machine.
Default: 50M.
fade (class Boolean)
If this is true, then when the screensaver activates, the current contents
of the screen will fade to black instead of simply winking out. This only
works on displays with writable colormaps, that is, if the screen's default
visual is a PseudoColor visual. A fade will also be done when
switching graphics hacks (when the cycle timer expires.)
Default: true.
unfade (class Boolean)
If this is true, then when the screensaver deactivates, the original contents
of the screen will fade in from black instead of appearing immediately. This
only works on displays with writable colormaps, and if fade is true
as well. Default false.
fadeSeconds (class Time)
If fade is true, this is how long the fade will be in
seconds (default 3 seconds.)
fadeTicks (class Integer)
If fade is true, this is how many times a second the colormap will
be changed to effect a fade. Higher numbers yield smoother fades, but
may make the fades take longer than the specified fadeSeconds if
your server isn't fast enough to keep up. Default 20.
captureStderr (class Boolean)
Whether xscreensaver should redirect its stdout and stderr streams to
the window itself. Since its nature is to take over the screen, you would not
normally see error messages generated by xscreensaver or the sub-programs it
runs; this resource will cause the output of all relevant programs to be
drawn on the screensaver window itself, as well as being written to the
controlling terminal of the screensaver driver process. Default true.
font (class Font)
The font used for the stdout/stderr text, if captureStderr is true.
Default *-medium-r-*-140-*-m-* (a 14 point fixed-width font.)
programs (class Programs)
The graphics hacks which xscreensaver runs when the user is idle.
The value of this resource is a string, one sh-syntax command per line.
Each line must contain exactly one command: no semicolons, no ampersands.
When the screensaver starts up, one of these is selected at random, and
run. After the cycle period expires, it is killed, and another
is selected and run.
If a line begins with a dash (-) then that particular program is
disabled: it won't be selected at random (though you can still select
it explicitly using the
xscreensaver-demo(1)
program.)
If all programs are disabled, then the screen will just be made blank.
To disable a program, it's better to mark it as disabled with a dash
than to remove it from the list. This is because the system-wide
(app-defaults) and per-user (.xscreensaver) settings are merged
together, and if a user just deletes an entry from their programs
list, but that entry still exists in the system-wide list, then it will
come back. However, if the user disables it, then their setting
takes precedence.
If the display has multiple screens, then a different program will be run
for each screen. (All screens are blanked and unblanked simultaniously.)
Note that you must escape the newlines; here is an example of how you
might set this in your ~/.xscreensaver file:
Make sure your $PATH environment variable is set up correctly
before xscreensaver is launched, or it won't be able to find the
programs listed in the programs resource.
To use a program as a screensaver, two things are required: that that
program draw on the root window (or be able to be configured to draw on
the root window); and that that program understand ``virtual root''
windows, as used by virtual window managers such as
tvtwm(1).
(Generally, this is accomplished by just including the "vroot.h"
header file in the program's source.)
If there are some programs that you want to run only when using a color
display, and others that you want to run only when using a monochrome
display, you can specify that like this:
More generally, you can specify the kind of visual that should be used for
the window on which the program will be drawing. For example, if one
program works best if it has a colormap, but another works best if it has
a 24-bit visual, both can be accommodated:
In addition to the symbolic visual names described above (in the discussion
of the visualID resource) one other visual name is supported in
the programs list:
default-n
This is like default, but also requests the use of the default colormap,
instead of a private colormap. (That is, it behaves as if
the -no-install command-line option was specified, but only for
this particular hack.) This is provided because some third-party programs
that draw on the root window (notably:
xv(1),
and
xearth(1))
make assumptions about the visual and colormap of the root window:
assumptions which xscreensaver can violate.
If you specify a particular visual for a program, and that visual does not
exist on the screen, then that program will not be chosen to run. This
means that on displays with multiple screens of different depths, you can
arrange for appropriate hacks to be run on each. For example, if one screen
is color and the other is monochrome, hacks that look good in mono can be
run on one, and hacks that only look good in color will show up on the other.
Normally you won't need to change the following resources:
pointerPollTime (class Time)
When server extensions are not in use, this controls how
frequently xscreensaver checks to see if the mouse position or buttons
have changed. Default 5 seconds.
windowCreationTimeout (class Time)
When server extensions are not in use, this controls the delay between when
windows are created and when xscreensaver selects events on them.
Default 30 seconds.
initialDelay (class Time)
When server extensions are not in use, xscreensaver will wait this many
seconds before selecting events on existing windows, under the assumption that
xscreensaver is started during your login procedure, and the window
state may be in flux. Default 0. (This used to default to 30, but that was
back in the days when slow machines and X terminals were more common...)
sgiSaverExtension (class Boolean)
There are a number of different X server extensions which can make
xscreensaver's job easier. The next few resources specify whether these
extensions should be utilized if they are available.
This resource controls whether the SGI SCREEN_SAVER server extension
will be used to decide whether the user is idle. This is the default
if xscreensaver has been compiled with support for this
extension (which is the default on SGI systems.). If it is available,
the SCREEN_SAVER method is faster and more reliable than what will
be done otherwise, so use it if you can. (This extension is only available
on Silicon Graphics systems, unfortunately.)
mitSaverExtension (class Boolean)
This resource controls whether the MIT-SCREEN-SAVER server extension
will be used to decide whether the user is idle. However, the default for
this resource is false, because even if this extension is available,
it is flaky (and it also makes the fade option not work properly.)
Use of this extension is not recommended.
xidleExtension (class Boolean)
This resource controls whether the XIDLE server extension will be
used to decide whether the user is idle. This is the default
if xscreensaver has been compiled with support for this extension.
(This extension is only available for X11R4 and X11R5 systems, unfortunately.)
procInterrupts (class Boolean)
This resource controls whether the /proc/interrupts file should be
consulted to decide whether the user is idle. This is the default
if xscreensaver has been compiled on a system which supports this
mechanism (i.e., Linux systems.)
The benefit to doing this is that xscreensaver can note that the user
is active even when the X console is not the active one: if the user is
typing in another virtual console, xscreensaver will notice that and will
fail to activate. For example, if you're playing Quake in VGA-mode,
xscreensaver won't wake up in the middle of your game and start competing
for CPU.
The drawback to doing this is that perhaps you really do want idleness
on the X console to cause the X display to lock, even if there is activity
on other virtual consoles. If you want that, then set this option to False.
(Or just lock the X console manually.)
The default value for this resource is True, on systems where it works.
overlayStderr (class Boolean)
If captureStderr is True, and your server supports ``overlay'' visuals,
then the text will be written into one of the higher layers instead of into
the same layer as the running screenhack. Set this to False to disable
that (though you shouldn't need to.)
overlayTextForeground (class Foreground)
The foreground color used for the stdout/stderr text, if captureStderr
is true. Default: Yellow.
overlayTextBackground (class Background)
The background color used for the stdout/stderr text, if captureStderr
is true. Default: Black.
bourneShell (class BourneShell)
The pathname of the shell that xscreensaver uses to start subprocesses.
This must be whatever your local variant of /bin/sh is: in particular,
it must not be csh.
COMMAND-LINE OPTIONS
xscreensaver
also accepts the following command line options. Except for
the -display option, these command-line options are all
simply shorthand for the X resources described in
the Configuration section, above.
-display host:display.screen
The X display to use. For displays with multiple screens, XScreenSaver
will manage all screens on the display simultaniously; the screen
argument (the ``default'' screen) says which screen should be used for
dialog boxes (the password window, Demo Mode, etc.)
-timeout minutes
Same as the timeout resource.
-cycle minutes
Same as the cycle resource.
-lock-mode
Same as setting the lock resource to true.
-no-lock-mode
Same as setting the lock resource to false.
-lock-timeout minutes
Same as the lockTimeout resource.
-visual visual
Same as the visualID resource.
-install
Same as setting the installColormap resource to true.
-no-install
Same as setting the installColormap resource to false.
-verbose
Same as setting the verbose resource to true.
-silent
Same as setting the verbose resource to false.
-timestamp
Same as setting the timestamp resource to true.
-capture-stderr
Same as setting the captureStderr resource to true.
-no-capture-stderr
Same as setting the captureStderr resource to false.
-splash
Same as setting the splash resource to true.
-no-splash
Same as setting the splash resource to false.
-nice integer
Same as the nice resource.
-sgi-extension
Same as setting the sgiSaverExtension resource to true.
-no-sgi-extension
Same as setting the sgiSaverExtension resource to false.
-mit-extension
Same as setting the mitSaverExtension resource to true.
-no-mit-extension
Same as setting the mitSaverExtension resource to false.
-xidle-extension
Same as setting the xidleExtension resource to true.
-no-xidle-extension
Same as setting the xidleExtension resource to false.
-proc-interrupts
Same as setting the procInterrupts resource to true.
-no-proc-interrupts
Same as setting the procInterrupts resource to false.
-xrm resource-specification
As with all other Xt programs, you can specify X resources on the command-line
using the -xrm argument. Most of the interesting resources have
command-line equivalents, however.
HOW IT WORKS
When it is time to activate the screensaver, a full-screen black window is
created on each screen of the display. Each window is created in such a way
that, to any subsequently-created programs, it will appear to be a ``virtual
root'' window. Because of this, any program which draws on the root
window (and which understands virtual roots) can be used as a screensaver.
When the user becomes active again, the screensaver windows are unmapped, and
the running subprocesses are killed by sending them SIGTERM. This is
also how the subprocesses are killed when the screensaver decides that it's
time to run a different demo: the old one is killed and a new one is launched.
Before launching a subprocess, xscreensaver stores an appropriate value
for $DISPLAY in the environment that the child will receive. (This is
so that if you start xscreensaver with a -display argument, the
programs which xscreensaver launches will draw on the same display;
and so that the child will end up drawing on the appropriate screen of a
multi-headed display.)
When the screensaver turns off, or is killed, care is taken to restore
the ``real'' virtual root window if there is one. Because of this, it is
important that you not kill the screensaver process with kill -9 if
you are running a virtual-root window manager. If you kill it with -9,
you may need to restart your window manager to repair the damage. This
isn't an issue if you aren't running a virtual-root window manager.
For all the gory details, see the commentary at the top of xscreensaver.c.
You can control a running screensaver process by using the
xscreensaver-command(1)
program (which see.)
POWER MANAGEMENT
Modern X servers contain support to power down the monitor after an idle
period. If the monitor has powered down, then xscreensaver will
notice this (after a few minutes), and will not waste CPU by drawing
graphics demos on a black screen. An attempt will also be made to
explicitly power the monitor back up as soon as user activity is detected.
As of version 3.28, the ~/.xscreensaver file controls the
configuration of your display's power management settings: if you have
used
xset(1)
to change your power management settings, then xscreensaver will
override those changes with the values specified
in ~/.xscreensaver (or with its built-in defaults, if there
is no ~/.xscreensaver file yet.)
To change your power management settings, run
xscreensaver-demo(1)
and change the various timeouts through the user interface.
Alternately, you can edit the ~/.xscreensaver file directly.
If the power management section is grayed out in the
xscreensaver-demo(1)
window, then that means that your X server does not support
the XDPMS extension, and so control over the monitor's power state
is not available.
If you're using a laptop, don't be surprised if changing the DPMS
settings has no effect: many laptops have monitor power-saving behavior
built in at a very low level that is invisible to Unix and X. On such
systems, you can typically only adjust the power-saving delays by
changing settings in the BIOS in some hardware-specific way.
You can run xscreensaver from your
xdm(1)
session, so that the screensaver will run even when nobody is logged
in on the console.
The trick to using xscreensaver with xdm is this: keep in mind the
two very different states in which xscreensaver will be running:
1: Nobody logged in.
If you're thinking of running xscreensaver from XDM at all, then it's
probably because you want graphics demos to be running on the console
when nobody is logged in there. In this case, xscreensaver will function
only as a screen saver, not a screen locker: it doesn't make sense
for xscreensaver to lock the screen, since nobody is logged in yet!
The only thing on the screen is the XDM login prompt.
2: Somebody logged in.
Once someone has logged in through the XDM login window, the situation is
very different. For example: now it makes sense to lock the screen (and
prompt for the logged in user's password); and now xscreensaver should
consult that user's ~/.xscreensaver file; and so on.
The difference between these two states comes down to a question of,
which user is the xscreensaver process running as? For the first
state, it doesn't matter. If you start xscreensaver in the usual
XDM way, then xscreensaver will probably end up running as root, which
is fine for the first case (the ``nobody logged in'' case.)
However, once someone is logged in, running as root is no longer fine:
because xscreensaver will be consulting root's .xscreensaver file
instead of that of the logged in user, and won't be prompting for the
logged in user's password, and so on. (This is not a security problem,
it's just not what you want.)
So, once someone has logged in, you want xscreensaver to be running as that
user. The way to accomplish this is to kill the old xscreensaver process
and start a new one (as the new user.)
The simplest way to accomplish all of this is as follows:
1: Launch xscreensaver before anyone logs in.
To the file /usr/lib/X11/xdm/Xsetup, add the lines
This will run xscreensaver as root, over the XDM login window.
Moving the mouse will cause the screen to un-blank, and allow the user
to type their password at XDM to log in.
2: Restart xscreensaver when someone logs in.
Near the top of the file /usr/lib/X11/xdm/Xsession, add those same lines:
xscreensaver-command -exit
xscreensaver &
When someone logs in, this will kill off the existing (root) xscreensaver
process, and start a new one, running as the user who has just logged in.
If the user's .xscreensaver file requests locking, they'll get it. They
will also get their own choice of timeouts, and graphics demos, and so on.
Alternately, each user could just put those lines in their
personal ~/.xsession files.
Make sure you have $PATH set up correctly in the Xsetup
and Xsession scripts, or xdm won't be able to
find xscreensaver, and/or xscreensaver won't be able to
find its graphics demos.
(If your system does not seem to be executing the Xsetup file, you
may need to configure it to do so: the traditional way to do this is
to make that file the value of the DisplayManager*setup resource
in the /usr/lib/X11/xdm/xdm-config file. See the man page for
xdm(1)
for more details.)
It is safe to run xscreensaver as root (as xdm is likely to do.)
If run as root, xscreensaver changes its effective user and group ids
to something safe (like "nobody") before connecting to the X server
or launching user-specified programs.
An unfortunate side effect of this (important) security precaution is that
it may conflict with cookie-based authentication.
If you get "connection refused" errors when running xscreensaver
from xdm, then this probably means that you have
xauth(1)
or some other security mechanism turned on. One way around this is to
add "xhost +localhost" to Xsetup, just before xscreensaver
is launched.
Note that this will give access to the X server to anyone capable of logging
in to the local machine, so in some environments, this might not be
appropriate. If turning off file-system-based access control is not
acceptable, then running xscreensaver from the Xsetup file
might not be possible, and xscreensaver will only work when running as
a normal, unprivileged user.
For more information on the X server's access control mechanisms, see the
man pages for
X(1),
Xsecurity(1),
xauth(1),
and
xhost(1).
The instructions for using xscreensaver with
gdm(1)
are almost the same as for using
xdm(1),
above. There are only two differences, really: instead
of editing /usr/lib/X11/xdm/Xsetup, edit the
file /etc/X11/gdm/Init/Default; and instead of
editing /usr/lib/X11/xdm/Xsession, edit one or all of the
files in the /etc/X11/gdm/Sessions/ directory. (Note that
the default session (/etc/X11/gdm/Sessions/Default) usually
simply executes /usr/lib/X11/xdm/Xsession, so be careful
you aren't initializing xscreensaver twice.)
All the same caveats apply for
gdm(1)
as for
xdm(1).
USING CDE (COMMON DESKTOP ENVIRONMENT)
The easiest way to use xscreensaver on a system with CDE is to simply
switch off the built-in CDE screensaver, and use xscreensaver instead;
and second, to tell the front panel to run
xscreensaver-command(1)
with the -lock option when the Lock icon is clicked.
To accomplish this involves five steps:
1: Switch off CDE's locker
Do this by turning off ``Screen Saver and Screen Lock'' in the
Screen section of the Style Manager.
2: Edit sessionetc
Edit the file ~/.dt/sessions/sessionetc and add to it the line
xscreensaver &
And make sure the sessionetc file is executable.
This will cause xscreensaver to be launched when you log in.
(As always, make sure that xscreensaver and the graphics demos are on
your $PATH; the path needs to be set in .cshrc
and/or .dtprofile, not .login.)
3: Create XScreenSaver.dt
Create a file called ~/.dt/types/XScreenSaver.dt with the following
contents:
This associates the CDE front panel ``Lock'' icon with the lock command
we just defined in step 3.
5: Restart
Select ``Restart Workspace Manager'' from the popup menu to make
your changes take effect. If things seem not to be working, check the
file ~/.dt/errorlog for error messages.
USING HP VUE (VISUAL USER ENVIRONMENT)
Since CDE is a descendant of VUE, the instructions for using xscreensaver
under VUE are similar to the above:
1: Switch off VUE's locker
Open the ``Style Manager'' and select ``Screen.''
Turn off ``Screen Saver and Screen Lock'' option.
2: Make sure you have a Session
Next, go to the Style Manager's, ``Startup'' page.
Click on ``Set Home Session'' to create a session, then
on ``Return to Home Session'' to select this session each
time you log in.
3: Edit vue.session
Edit the file ~/.vue/sessions/home/vue.session and add to it
the line
vuesmcmd -screen 0 -cmd "xscreensaver"
This will cause xscreensaver to be launched when you log in.
(As always, make sure that xscreensaver and the graphics demos are on
your $PATH; the path needs to be set in .cshrc
and/or .profile, not .login.)
3: Edit vuewmrc
Edit the file ~/.vue/vuewmrc and add (or change) the Lock control:
CONTROL Lock
{
TYPE button
IMAGE lock
PUSH_ACTION f.exec "xscreensaver-command -lock"
HELP_TOPIC FPLock
}
This associates the VUE front panel ``Lock'' icon with the xscreensaver
lock command.
ADDING TO MENUS
The
xscreensaver-command(1)
program is a perfect candidate for something to add to your window manager's
popup menus. If you use
mwm(1),
4Dwm(1),
twm(1),
or (probably) any of twm's many descendants, you can do it like this:
1. Create ~/.mwmrc (or ~/.twmrc or ...)
If you don't have a ~/.mwmrc file (or, on SGIs, a ~/.4Dwmrc file;
or, with twm, a ~/.twmrc file) then create one by making a copy of
the /usr/lib/X11/system.mwmrc
file (or /usr/lib/X11/twm/system.twmrc, and so on.)
For
mwm(1)
and
4Dwm(1),
find the section of the file that says Menu DefaultRootMenu.
For
twm(1),
it will probably be menu "defops". If you add a line somewhere
in that menu definition that reads
"XScreenSaver" f.menu XScreenSaver
then this will add an XScreenSaver sub-menu to your default root-window
popup menu. Alternately, you could just put the xscreensaver menu items
directly into the root menu.
For Fvwm2, the process is similar: first create a ~/.fvwm2rc file
if you don't already have one, by making a copy of
the /etc/X11/fvwm2/system.fvwm2rc file. Then, add a menu definition
to it:
AddToMenu XScreenSaver "XScreenSaver" Title
+ "Blank Screen Now" Exec xscreensaver-command -activate
+ "Lock Screen Now" Exec xscreensaver-command -lock
+ "Screen Saver Demo" Exec xscreensaver-command -demo
+ "Screen Saver Preferences" Exec xscreensaver-command -prefs
+ "Reinitialize Screen Saver" Exec xscreensaver-command -restart
+ "Kill Screen Saver" Exec xscreensaver-command -exit
+ "Launch Screen Saver" Exec xscreensaver
+ "Run Next Demo" Exec xscreensaver-command -next
+ "Run Previous Demo" Exec xscreensaver-command -prev
# To put the XScreenSaver sub-menu at the end of the root menu:
AddToMenu RootMenu "XScreenSaver" Popup XScreenSaver
The Enlightenment window manager keeps each of its menus in a separate
file. So, you need to create a file
named ~/.enlightenment/xscreensaver.menu with the contents:
to ~/.enlightenment/file.menu to put the XScreenSaver submenu on
your left-button root-window menu.
As you see, every window manager does this stuff gratuitously differently,
just to make your life difficult. You are in a maze of twisty menu
configuration languages, all alike.
BUGS
Bugs? There are no bugs. Ok, well, maybe. If you find one, please let
me know. http://www.jwz.org/xscreensaver/bugs.html explains how to
construct the most useful bug reports.
Locking and XDM
If xscreensaver has been launched from
xdm(1)
before anyone has logged in, you will need to kill and then restart the
xscreensaver daemon after you have logged in, or you will be confused by
the results. (For example, locking won't work, and your ~/.xscreensaver
file will be ignored.)
When you are logged in, you want the xscreensaver daemon to be
running under your user id, not as root or some other user.
If it has already been started by xdm, you can kill it by sending
it the exit command, and then re-launching it as you, by putting
something like the following in your personal X startup script:
xscreensaver-command -exit
xscreensaver &
The ``Using XDM(1)'' section, above, goes into more detail, and explains
how to configure the system to do this for all users automatically.
Locking and root logins
In order for it to be safe for xscreensaver to be launched by xdm,
certain precautions had to be taken, among them that xscreensaver never
runs as root. In particular, if it is launched as root (as xdm
is likely to do), xscreensaver will disavow its privileges, and switch
itself to a safe user id (such as nobody.)
An implication of this is that if you log in as root on the console,
xscreensaver will refuse to lock the screen (because it can't tell
the difference between root being logged in on the console, and a
normal user being logged in on the console but xscreensaver having been
launched by the
xdm(1)
Xsetup
file.)
The solution to this is simple: you shouldn't be logging in on the console
as root in the first place! (What, are you crazy or something?)
Proper Unix hygiene dictates that you should log in as yourself, and
su(1)
to root as necessary. People who spend their day logged in
as root are just begging for disaster.
XAUTH and XDM
For xscreensaver to work when launched by
xdm(1),
programs running on the local machine as user "nobody" must be
able to connect to the X server. This means that if you want to run
xscreensaver on the console while nobody is logged in, you may need
to disable cookie-based access control (and allow all users who can log
in to the local machine to connect to the display.)
You should be sure that this is an acceptable thing to do in your
environment before doing it. See the ``Using XDM(1)'' section,
above, for more details.
If anyone has suggestions on how xscreensaver could be made to work with
xdm(1)
without first turning off .Xauthority-based access control, please
let me know.
Passwords
If you get an error message at startup like ``couldn't get password
of user'' then this probably means that you're on a system in which
the
getpwent(3)
library routine can only be effectively used by root. If this is the case,
then xscreensaver must be installed as setuid to root in order for
locking to work. Care has been taken to make this a safe thing to do.
It also may mean that your system uses shadow passwords instead of the standard
getpwent(3)
interface; in that case, you may need to change some options
with configure and recompile.
If you change your password after xscreensaver has been launched, it will
continue using your old password to unlock the screen until xscreensaver
is restarted. So, after you change your password, you'll have to do
xscreensaver-command -restart
to make xscreensaver notice.
PAM Passwords
If your system uses PAM (Pluggable Authentication Modules), then in order
for xscreensaver to use PAM properly, PAM must be told about xscreensaver.
The xscreensaver installation process should update the PAM data (on Linux,
by creating the file /etc/pam.d/xscreensaver for you, and on Solaris,
by telling you what lines to add to the /etc/pam.conf file.)
If the PAM configuration files do not know about xscreensaver, then
you might be in a situation where xscreensaver will refuse to ever
unlock the screen.
This is a design flaw in PAM (there is no way for a client to tell the
difference between PAM responding ``I have never heard of your module,''
and responding, ``you typed the wrong password.'') As far as I can tell,
there is no way for xscreensaver to automatically work around this, or
detect the problem in advance, so if you have PAM, make sure it is
configured correctly!
Colormap lossage: TWM
The installColormap option doesn't work very well with the
twm(1)
window manager and its descendants.
There is a race condition between the screensaver and this window manager,
which can result in the screensaver's colormap not getting installed
properly, meaning the graphics hacks will appear in essentially random
colors. (If the screen goes white instead of black, this is probably why.)
The
mwm(1)
and
olwm(1)
window managers don't have this problem. The race condition exists
because X (really, ICCCM) does not provide a way for an OverrideRedirect
window to have its own colormap, short of grabbing the server (which is
neither a good idea, nor really possible with the current design.) What
happens is that, as soon as xscreensaver installs its colormap, twm
responds to the resultant ColormapNotify event by re-instaling the
default colormap. Apparently, twm doesn't always do this; it
seems to do it regularly if the screensaver is activated from a menu item,
but seems to not do it if the screensaver comes on of its own volition, or
is activated from another console.
Attention, window manager authors!
You should only call
XInstallColormap(3)
in response to user events. That is, it is appropriate to install a colormap
in response to FocusIn, FocusOut, EnterNotify,
and LeaveNotify events; but it is not appropriate to call it in
response to ColormapNotify events. If you install colormaps in
response to application actions as well as in response to user
actions, then you create the situation where it is impossible for
override-redirect applications (such as xscreensaver) to display their
windows in the proper colors.
Colormap lossage: XV, XAnim, XEarth
Some programs don't operate properly on visuals other than the default one,
or with colormaps other than the default one. See the discussion of the
magic "default-n" visual name in the description of the programs
resource in the Configuration section. When programs only work with
the default colormap, you need to use a syntax like this:
It would also work to turn off the installColormap option altogether,
but that would deny extra colors to those programs that can take
advantage of them.
Machine Load
Although this program ``nices'' the subprocesses that it starts,
graphics-intensive subprograms can still overload the machine by causing
the X server process itself (which is not ``niced'') to suck a lot of
cycles. Care should be taken to slow down programs intended for use as
screensavers by inserting strategic calls to
sleep(3)
or
usleep(3)
(or making liberal use of any -delay options which the programs
may provide.)
Note that the OpenGL-based graphics demos are real pigs on machines that
don't have texture hardware.
Also, an active screensaver will cause your X server to be pretty much
permanently swapped in; but the same is true of any program that draws
periodically, like
xclock(1)
or
xload(1).
Latency and Responsiveness
If the subprocess is drawing too quickly and the connection to the X
server is a slow one (such as an X terminal running over a phone line) then
the screensaver might not turn off right away when the user becomes active
again (the
ico(1)
demo has this problem if being run in full-speed mode). This can be
alleviated by inserting strategic calls to
XSync(3)
in code intended for use as a screensaver. This prevents too much graphics
activity from being buffered up.
XFree86's Magic Keystrokes
The XFree86 X server traps certain magic keystrokes before client programs ever
see them. Two that are of note are Ctrl+Alt+Backspace, which causes
the X server to exit; and Ctrl+Alt+Fn, which switches virtual consoles.
The X server will respond to these keystrokes even if xscreensaver has the
screen locked. Depending on your setup, you might consider this a problem.
Unfortunately, there is no way for xscreensaver itself to override the
interpretation of these keys. If you want to disable Ctrl+Alt+Backspace
globally, you need to set the DontZap flag in
your /etc/X11/XF86Config file. See the
XF86Config(5)
manual for details.
There is no way (as far as I can tell) to disable the VT-switching keystrokes.
Some Linux systems come with a VT_LOCKSWITCH ioctl, that one could
theoretically use to prevent VT-switching while the screen is locked;
but unfortunately, this ioctl can only be used by root, which means
that xscreensaver can't use it (since xscreensaver disavows its privileges
shortly after startup, for security reasons.)
Any suggestions for other solutions to this problem are welcome.
XView Clients
Apparently there are some problems with XView programs getting confused
and thinking that the screensaver window is the real root window even when
the screensaver is not active: ClientMessages intended for the window manager
are sent to the screensaver window instead. This could be solved by making
xscreensaver forward all unrecognised ClientMessages to the real root window,
but there may be other problems as well. If anyone has any insight on the
cause of this problem, please let me know. (XView is an X11 toolkit that
implements the (quite abominable) Sun OpenLook look-and-feel.)
MIT Extension and Fading
The MIT-SCREEN-SAVER extension is junk. Don't use it.
When using the MIT-SCREEN-SAVER extension in conjunction with
the fade option, you'll notice an unattractive flicker just before
the fade begins. This is because the server maps a black window just before
it tells the xscreensaver process to activate. The xscreensaver
process immediately unmaps that window, but this results in a flicker. I
haven't figured a way to get around this; it seems to be a fundamental
property of the (mis-) design of this server extension.
It sure would be nice if someone would implement the SGI SCREEN_SAVER
extension in XFree86; it's dead simple, and works far better than the
overengineered and broken MIT-SCREEN-SAVER extension.
SGI Power Saver
If you're running Irix 6.3, you might find that your monitor is powering down
after an hour or two even if you've told it not to. This is fixed by SGI
patches 2447 and 2537.
If you're running Irix 6.5, this bug is back. I don't know a fix.
MesaGL and Voodoo Cards
If you have a 3Dfx/Voodoo card, the default settings for xscreensaver will
run the GL-based graphics demos in such a way that they will not take
advantage of the 3D acceleration hardware. The solution is to change
the programs entries for the GL hacks from this:
gears -root \n\
to this:
MESA_GLX_FX=fullscreen gears \n\
That is, make sure that $MESA_GLX_FX is set to fullscreen, and
don't tell the program to draw on the root window. This may seem strange,
but the setup used by Mesa and these kinds of cards is strange!
For those who don't know, these cards work by sitting between your normal
video card and the monitor, and seizing control of the monitor when it's
time to do 3D. But this means that accelerated 3D only happens in full-screen
mode (you can't do it in a window, and you can't see the output of 3D and 2D
programs simultaniously), and that 3D will probably drive your monitor at a
lower resolution, as well. It's bizarre.
If you find that GL programs only work properly when run as root, and not
as normal users, then the problem is that your /dev/3dfx file is not
configured properly. Check the Linux 3Dfx FAQ.
Keyboard LEDs
If procInterrupts is on (which is the default on Linux systems) and
you're using some program that toggles the state of your keyboard LEDs,
xscreensaver won't work right: turning those LEDs on or off causes a
keyboard interrupt, which xscreensaver will interpret as user activity.
So if you're using such a program, set the procInterrupts resource
to False.
Extensions
If you are not making use of one of the server extensions (XIDLE,
SGI SCREEN_SAVER, or MIT-SCREEN-SAVER), then it is possible, in
rare situations, for xscreensaver to interfere with event propagation
and make another X program malfunction. For this to occur, that other
application would need to not select KeyPress events on its
non-leaf windows within the first 30 seconds of their existence, but then
select for them later. In this case, that client might fail to receive
those events. This isn't very likely, since programs generally select a
constant set of events immediately after creating their windows and then
don't change them, but this is the reason that it's a good idea to install
and use one of the server extensions instead, to work around this shortcoming
in the X protocol.
In all these years, I've not heard of even a single case of this happening,
but it is theoretically possible, so I'm mentioning it for completeness...
Red Hot Lava
There need to be a lot more graphics hacks. In particular, there should be
a simulation of a Lavalite (tm).
ENVIRONMENT
DISPLAY
to get the default host and display number, and to inform the sub-programs
of the screen on which to draw.
PATH
to find the sub-programs to run.
HOME
for the directory in which to read and write the .xscreensaver file.
XENVIRONMENT
to get the name of a resource file that overrides the global resources
stored in the RESOURCE_MANAGER property.