fping - send ICMP ECHO_REQUEST packets to network hosts
SYNOPSIS
fping
[ options ]
[ systems... ]
DESCRIPTION
fping
is a
like program which uses the Internet Control
Message Protocol (ICMP) echo request to determine if a target host is
responding.
fping
differs from ping in that you can specify any
number of targets on the command line, or specify a file containing
the lists of targets to ping. Instead of sending to one target until it
times out or replies,
fping
will send out a ping packet and move
on to the next target in a round-robin fashion.
In the default mode, if a target replies,
it is noted and removed from the list of targets to check; if a target
does not respond within a certain time limit and/or retry limit it
is designated as unreachable.
fping
also supports sending a specified number of pings to a target, or
looping indefinitely (as in
ping
).
Unlike
ping
,
fping
is meant to be used in scripts, so its output is designed to be
easy to parse.
OPTIONS
-a
Show systems that are alive.
-A
Display targets by address rather than DNS name.
-bn
Number of bytes of ping data to send. The minimum size (normally 12)
allows room for the data that
fping
needs to do its work (sequence number, timestamp). The reported
received data size includes the IP header (normally 20 bytes) and ICMP
header (8 bytes), so the minimum total size is 40 bytes. Default is
56, as in
ping.
Maximum is the theoretical maximum IP datagram size (64K), though most
systems limit this to a smaller, system-dependent number.
-Bn
In the default mode,
fping
sends several requests to a target before giving up, waiting longer for
a reply on each successive request. This parameter is the value by
which the wait time is multiplied on each successive request; it must
be entered as a floating-point number (x.y). The default is 1.5.
-c
Number of request packets to send to each target. In this mode, a
line is displayed for each received response (this can suppressed with
-q or -Q). Also, statistics about responses for each target are displayed
when all requests have been sent (or when interrupted).
-C
Similar to -c, but the per-target statistics are displayed in a format
designed for automated response-time statistics gathering. For
example:
% fping -C 5 -q somehost
somehost : 91.7 37.0 29.2 - 36.8
shows the response time in milliseconds for each of the five requests,
with the "-" indicating that no response was received to the fourth
request.
-d
Use DNS to lookup address of return ping packet. This allows you to give
fping a list of IP addresses as input and print hostnames in the output.
-e
Show elapsed (round-trip) time of packets.
-f
Read list of targets from a file. This option can only be used by the
root user. Regular users should pipe in the file via stdin:
% fping < targets_file
-g
Generate a target list from a supplied IP netmask, or a starting and ending IP.
Specify the netmask or start/end in the targets portion of the command line.
ex. To ping the class C 192.168.1.x, the specified command line could look like either:
fping -g 192.168.1.0/24
or
fping -g 192.168.1.0 192.168.1.255
-h
Print usage message.
-in
The minimum amount of time (in milliseconds) between sending a ping packet to any target (default is 25).
-l
Loop sending packets to each target indefinitely. Can be interrupted
with ctl-C; statistics about responses for each target are then displayed.
-m
Send pings to each of a target host's multiple interfaces.
-n
Same as -d.
-p
In looping or counting modes (-l, -c, or -C), this parameter sets the
time in milliseconds that
fping
waits between successive packets to an individual target. Default is
1000.
-q
Quiet. Don't show per-target results, just set final exit status.
-Qn
Like -q, but show summary results every n seconds.
-rn
Retry limit (default 3). This is the number of times an attempt at pinging
a target will be made, not including the first try.
-s
Print cumulative statistics upon exit.
-tn
Initial target timeout in milliseconds (default 500). In the default
mode, this is the amount of time that
fping
waits for a response to its first request. Successive timeouts are
multiplied by the backoff factor.
-u
Show targets that are unreachable.
-v
Print
fping
version information.
EXAMPLES
The following perl script will check a list of hosts and send mail if
any are unreachable. It uses the open2 function which allows a program
to be opened for reading and writing. fping does not start pinging the
list of systems until it reads EOF, which it gets after INPUT is closed.
Sure the open2 usage is not needed in this example, but it's a good open2
example none the less.
#!/usr/bin/perl
require 'open2.pl';
$MAILTO = "root";
$pid = &open2("OUTPUT","INPUT","/usr/local/bin/fping -u");
@check=("slapshot","foo","foobar");
foreach(@check) { print INPUT "$_\n"; }
close(INPUT);
@output=<OUTPUT>;
if ($#output != -1) {
chop($date=`date`);
open(MAIL,"|mail -s 'unreachable systems' $MAILTO");
print MAIL "\nThe following systems are unreachable as of: $date\n\n";
print MAIL @output;
close MAIL;
}
Another good example is when you want to perform an action only on hosts
that are currently reachable.
#!/usr/bin/perl
$hosts_to_backup = `cat /etc/hosts.backup | fping -a`;
foreach $host (split(/\n/,$hosts_to_backup)) {
# do it
}
AUTHORS
Roland J. Schemers III, Stanford University, concept and versions 1.x
RL "Bob" Morgan, Stanford University, versions 2.x
David Papp, versions 2.3x and up,
fping website: http://www.fping.com
DIAGNOSTICS
Exit status is 0 if all the hosts are reachable, 1 if some hosts were
unreachable, 2 if any IP addresses were not found, 3 for invalid
command line arguments, and 4 for a system call failure.
BUGS
Ha! If we knew of any we would have fixed them!
RESTRICTIONS
If certain options are used (i.e, a low value for -i and -t, and a
high value for -r) it is possible to flood the network. This program
must be installed as setuid root in order to open up a raw socket,
or must be run by root. In order to stop mere mortals from hosing the
network (when fping is installed setuid root) , normal users can't specify
the following:
-i n where n < 10 msec
-r n where n > 20
-t n where n < 250 msec