Manpages

sane-umax

NAME

ABOUT THIS FILE

This file only is a short descripton of the umax-backend for sane! For detailled information take a look at sane-umax-doc.html (it is included in the sane source directory and in the xsane online help)!

DESCRIPTION

The sane-umax library implements a SANE backend that provides acces to several UMAX-SCSI-scanners and some Linotye Hell SCSI-scanners, parallel- and USB-scanners are not (and propably will never be) supported!

I suggest you hold one hand on the power-button of the scanner while you try the first scans!

CONFIGURATION

The configuration file for this backend resides in         /etc/sane.d/umax.conf.

Its contents is a list of device names that correspond to UMAX and UMAX compatible scanners. Empty lines and lines starting with a hash mark (#) are ignored. A sample configuration file is shown below:

 # this is a comment
 #
 option scsi-maxqueue 4
 option scsi-buffer-size-min 65536
 option scsi-buffer-size-max 131072
 option scan-lines 40
 option preview-lines 10
 option scsi-maxqueue 2
 option execute-request-sense 0
 option force-preview-bit-rgb 0
 option slow-speed -1
 option care-about-smearing -1
 option calibration-full-ccd -1
 option calibration-width-offset -1
 option calibration-bytes-pixel -1
 option invert-shading-data -1 
 option lamp-control-available 0
 option gamma-lsb-padded 0
 /dev/sge 

 #scsi Vendor Model Type Bus Channel ID LUN 
 # The following scanner supports lamp control
 option lamp-control-available 1
 scsi UMAX * Scanner * * * * * 

 # scanner on /dev/scanner does not support lamp control
 option lamp-control-available 0
 /dev/scanner 

 - execute-request-sense:
   values:
    0 = disabled
    1 = enabled
   default = 0
   If set to 1 umax_do_request_sense is called in
   umax_do_calibration. This can hang the system
   (but has been enabled until this version)
 
 - scsi-buffer-size-min, scsi-buffer-size-max:
   values: 4096-1048576, default min=32768, max=131072
   Especially the minimum value is very important.
   If this value is set too small the backend is not
   able to send gamma tables to the scanner or to
   do a correct color calibration. This may result in
   strange color effects. If the minimum value is set
   too large then the backend is not able to allocate
   the requested scsi buffer size and aborts with
   out of memory error. The default is 32KB, for
   some scanners it should be increased to 64KB.
 
 - scan-lines, preview-lines:
   values: 1-65535,
   default: scan-lines=40, preview-lines=10
   define the maximum number of lines that are scanned
   into one buffer
 
 - force-preview-bit-rgb:
   values:
    0 = disabled
    1 = enabled
   default = 0
   set preview bit in rgb real scan
 
 - slow-speed, care-about-smearing:
   values:
   -1 = auto
    0 = disabled
    1 = enabled
   default = -1
   dangerous options, needed for some scanners
   do not changed these options until you really know
   what you do, you may destroy your scanner when you
   define wrong values for this options
 
 - calibration-full-ccd:
   values:
   -1 = auto
    0 = disabled
    1 = enabled
   default = -1
   do calibration for each pixel of ccd instead of
   selected image
 
 - calibration-width-offset:
   values: -99999=auto, >-99999 set value
   add an offset width to the calculated with for
   image/ccd
 
 - calibration-bytes-pixel:
   values:
   -1 = disabled
    0 = not set
    1 = 1 byte/pixel,
    2 = 2 bytes/pixel
   use # bytes per pixel for calibration
 
 - invert-shading-data:
   values:
   -1 = automatically set by driver - if known
    0 = disabled
    1 = enabled
   default = -1
   invert shading data before sending it back to the scanner
 
 - lamp-control-available:
   values:
    0 = automatically set by driver - if known
    1 = available
   default = 0

 - gamma-lsb-padded:
   values:
   -1 = automatically set by driver - if known
    0 = gamma data is msb padded
    1 = gamma data is lsb padded
   default = -1

 - handle-bad-sense-error:
   values:
    0 = handle as device busy
    1 = handle as ok
    2 = handle as i/o error
    3 = ignore bad error code - continue sense handler,
   default = 0

 - scsi-maxqueue:
   values:
    1..# (maximum defined at compile time)
   default = 2
   most scsi drivers allow internal command queueing with a depth
   of 2 commands. In most cases it does not mprove anything when you
   increase this value. When your scsi driver does not support any
   command queueing you can try to set this value to 1.
   

The special device name must be a generic SCSI device or a symlink to such a device. To find out to which device your scanner is assigned and how you have to set the permissions of that device, have a look at sane-scsi.

SCSI ADAPTER TIPS

The ISA-SCSI-adapters that are shipped with some Umax-scanners are not supported very well by Linux (I suggest not to use it), the PCI-SCSI-adapters that come with some Umax-scanners are not supported at all (as far as I know). On other platforms these SCSI-adapters are not supported. So you typically need to purchase another SCSI-adapter that is supported by your platform. See the relevant hardware FAQs and HOWTOs for your platform for more information.

The UMAX-scanners do block the scsi-bus for a few seconds while scanning. It is not necessary to connect the scanner to its own SCSI-adapter. But if you need short response time for your SCSI-harddisk (e.g. if your computer is a file-server) or other scsi devices, I suggest you use an own SCSI-adapter for your UMAX-scanner.

If you have any problems with your Umax scanner, check your scsi chain (cable length, termination, ...).

See also: sane-scsi(5)

FILES

The backend configuration file:
 /etc/sane.d/umax.conf

The static library implementing this backend:
 /usr/lib/sane/libsane-umax.a

The shared library implementing this backend :
 /usr/lib/sane/libsane-umax.so
 (present on systems that support dynamic loading)

ENVIRONMENT

SANE_DEBUG_UMAX
 If the library was compiled with debug support enabled, this environment variable controls the debug level for this backend. E.g., a value of 128 requests all debug output to be printed. Smaller levels reduce verbosity: SANE_DEBUG_UMAX values

 Number  Remark
 0       print important errors (printed each time)
 1       print errors
 2       print sense
 3       print warnings
 4       print scanner-inquiry
 5       print informations
 6       print less important informations
 7       print called procedures
 8       print reader_process messages
 10      print called sane-init-routines
 11      print called sane-procedures
 12      print sane infos
 13      print sane option-control messages
Example:
export SANE_DEBUG_UMAX=8

BUGS

X-resolutions greater than 600 dpi sometimes make problems

SEE ALSO

AUTHOR

Oliver Rauch

EMAIL-CONTACT

Index

NAME

ABOUT THIS FILE

DESCRIPTION

CONFIGURATION

SCSI ADAPTER TIPS

FILES

ENVIRONMENT

BUGS

SEE ALSO

AUTHOR

EMAIL-CONTACT