CDRTOOLS compiles without changes on any UnixWare 7.0.1 or later installation having the UnixWare/OpenServer DevKit (UODK) or GCC-2.95 and smake-1.2 installed. You can get pre-packaged, pkgadd installable binaries from: http://www.sco.com/skunkware/cdrtools Some general notes on CDRTOOLS are available from: http://www.sco.com/skunkware/cdrtools/SCO-NOTES.html Limitations for CDRTOOLS-1.8 on UnixWare: 1) SCO UnixWare 2.1.X and UnixWare 7.0.0 are not supported - UW2.1.X will compile/work with little changes - UW7.0.0 wasn't tested at all 2) There is only support for SCSI devices 3) UnixWare 7.0.1 requires additional PTF's to enable some host bus adapters to work with a logical block size of more than 512 bytes. (Please see the above SCO_NOTES document for details!) =================================================================== NOTE: cdrecord now supports the -scanbus option. Therefore the old addressing methods are NO LONGER AVAILABLE !!! As UnixWare 7.1.1 doesn't allow to open the passthrough interface for disks, this is disabled by default. cdrecord -scanbus will therefore only list devices other than disks. To enable the scanning of disks, you need to set an environment variable "LIBSCG_SCAN_ALL". Be warned, doing so might lock your disk subsystem! =================================================================== The correct dev= syntax on UnixWare 7 is: dev=scsibus,target,lun (and scsibus is scsibus now!!!) A sample output from cdrecord -scanbus looks like: #cdrecord -scanbus Cdrecord 1.8 (i586-sco-sysv5uw7.0.1) Copyright (C) 1995-2000 Jörg Schilling Using libscg version 'schily-0.1' scsibus0: 0,0,0 0) 'SEAGATE ' 'ST34573LC ' '5960' Disk 0,1,0 1) 'SEAGATE ' 'ST34573LC ' '5960' Disk 0,2,0 2) 'SEAGATE ' 'ST34573LC ' '5960' Disk 0,3,0 3) * 0,4,0 4) * 0,5,0 5) 'PIONEER ' 'CD-ROM DR-U06S ' '1.05' Removable CD-ROM 0,6,0 6) 'TEAC ' 'CD-R56S ' '1.0E' Removable CD-ROM 0,7,0 7) * The first column showing the triple x,y,z tells you the address to use. As you can see the TEAC CD-R56S CD-Writer does have the following address: dev=0,6,0 =================================================================== THE OLD ADDRESSING IS NO LONGER AVAILABLE! PLEASE ADJUST YOUR /etc/default/cdrecord FILES! =================================================================== Running cdrecord with the old address method will result in an error! #cdrecord dev=/dev/rcdrom/cdrom1:6,0 -inq Cdrecord 1.8 (i386-pc-sco3.2v5.0.5) Copyright (C) 1995-2000 Jörg Schilling scsidev: '/dev/rcd1:6,0' devname: '/dev/rcd1' scsibus: 0 target: 6 lun: 0 cdrecord: Invalid argument. Open by 'devname' no longer supported on this OS. Cannot open SCSI driver. cdrecord: For possible targets try 'cdrecord -scanbus'. Make sure you are root. To compile cdrtools, you need 'smake' from: ftp://ftp.sco.com/skunkware/uw7/Packages or 'gmake'. Smake is preferred as gmake bugs will cause bogus warnings and may confuse about the state of the make run.