GNU Info

(gdb.info)MIPS Embedded

---

Next: PA Prev: M88K Up: Embedded Processors

---

Enter node , (file) or (file)node

MIPS Embedded
-------------

   GDB can use the MIPS remote debugging protocol to talk to a MIPS
board attached to a serial line.  This is available when you configure
GDB with `--target=mips-idt-ecoff'.

   Use these GDB commands to specify the connection to your target
board:

`target mips PORT'
     To run a program on the board, start up `gdb' with the name of
     your program as the argument.  To connect to the board, use the
     command `target mips PORT', where PORT is the name of the serial
     port connected to the board.  If the program has not already been
     downloaded to the board, you may use the `load' command to
     download it.  You can then use all the usual GDB commands.

     For example, this sequence connects to the target board through a
     serial port, and loads and runs a program called PROG through the
     debugger:

          host$ gdb PROG
          GDB is free software and ...
          (gdb) target mips /dev/ttyb
          (gdb) load PROG
          (gdb) run

`target mips HOSTNAME:PORTNUMBER'
     On some GDB host configurations, you can specify a TCP connection
     (for instance, to a serial line managed by a terminal
     concentrator) instead of a serial port, using the syntax
     `HOSTNAME:PORTNUMBER'.

`target pmon PORT'
     PMON ROM monitor.

`target ddb PORT'
     NEC's DDB variant of PMON for Vr4300.

`target lsi PORT'
     LSI variant of PMON.

`target r3900 DEV'
     Densan DVE-R3900 ROM monitor for Toshiba R3900 Mips.

`target array DEV'
     Array Tech LSI33K RAID controller board.

GDB also supports these special commands for MIPS targets:

`set processor ARGS'
`show processor'
     Use the `set processor' command to set the type of MIPS processor
     when you want to access processor-type-specific registers.  For
     example, `set processor R3041' tells GDB to use the CPU registers
     appropriate for the 3041 chip.  Use the `show processor' command
     to see what MIPS processor GDB is using.  Use the `info reg'
     command to see what registers GDB is using.

`set mipsfpu double'
`set mipsfpu single'
`set mipsfpu none'
`show mipsfpu'
     If your target board does not support the MIPS floating point
     coprocessor, you should use the command `set mipsfpu none' (if you
     need this, you may wish to put the command in your GDB init file).
     This tells GDB how to find the return value of functions which
     return floating point values.  It also allows GDB to avoid saving
     the floating point registers when calling functions on the board.
     If you are using a floating point coprocessor with only single
     precision floating point support, as on the R4650 processor, use
     the command `set mipsfpu single'.  The default double precision
     floating point coprocessor may be selected using `set mipsfpu
     double'.

     In previous versions the only choices were double precision or no
     floating point, so `set mipsfpu on' will select double precision
     and `set mipsfpu off' will select no floating point.

     As usual, you can inquire about the `mipsfpu' variable with `show
     mipsfpu'.

`set remotedebug N'
`show remotedebug'
     You can see some debugging information about communications with
     the board by setting the `remotedebug' variable.  If you set it to
     `1' using `set remotedebug 1', every packet is displayed.  If you
     set it to `2', every character is displayed.  You can check the
     current value at any time with the command `show remotedebug'.

`set timeout SECONDS'
`set retransmit-timeout SECONDS'
`show timeout'
`show retransmit-timeout'
     You can control the timeout used while waiting for a packet, in
     the MIPS remote protocol, with the `set timeout SECONDS' command.
     The default is 5 seconds.  Similarly, you can control the timeout
     used while waiting for an acknowledgement of a packet with the `set
     retransmit-timeout SECONDS' command.  The default is 3 seconds.
     You can inspect both values with `show timeout' and `show
     retransmit-timeout'.  (These commands are _only_ available when
     GDB is configured for `--target=mips-idt-ecoff'.)

     The timeout set by `set timeout' does not apply when GDB is
     waiting for your program to stop.  In that case, GDB waits forever
     because it has no way of knowing how long the program is going to
     run before stopping.