GNU Info

Info Node: (libc.info)Editing Characters

(libc.info)Editing Characters


Next: Signal Characters Up: Special Characters
Enter node , (file) or (file)node

Characters for Input Editing
............................

   These special characters are active only in canonical input mode.
Note: Canonical or Not.

 - Macro: int VEOF
     This is the subscript for the EOF character in the special control
     character array.  `TERMIOS.c_cc[VEOF]' holds the character itself.

     The EOF character is recognized only in canonical input mode.  It
     acts as a line terminator in the same way as a newline character,
     but if the EOF character is typed at the beginning of a line it
     causes `read' to return a byte count of zero, indicating
     end-of-file.  The EOF character itself is discarded.

     Usually, the EOF character is `C-d'.

 - Macro: int VEOL
     This is the subscript for the EOL character in the special control
     character array.  `TERMIOS.c_cc[VEOL]' holds the character itself.

     The EOL character is recognized only in canonical input mode.  It
     acts as a line terminator, just like a newline character.  The EOL
     character is not discarded; it is read as the last character in
     the input line.

     You don't need to use the EOL character to make <RET> end a line.
     Just set the ICRNL flag.  In fact, this is the default state of
     affairs.

 - Macro: int VEOL2
     This is the subscript for the EOL2 character in the special control
     character array.  `TERMIOS.c_cc[VEOL2]' holds the character itself.

     The EOL2 character works just like the EOL character (see above),
     but it can be a different character.  Thus, you can specify two
     characters to terminate an input line, by setting EOL to one of
     them and EOL2 to the other.

     The EOL2 character is a BSD extension; it exists only on BSD
     systems and the GNU system.

 - Macro: int VERASE
     This is the subscript for the ERASE character in the special
     control character array.  `TERMIOS.c_cc[VERASE]' holds the
     character itself.

     The ERASE character is recognized only in canonical input mode.
     When the user types the erase character, the previous character
     typed is discarded.  (If the terminal generates multibyte
     character sequences, this may cause more than one byte of input to
     be discarded.)  This cannot be used to erase past the beginning of
     the current line of text.  The ERASE character itself is discarded.

     Usually, the ERASE character is <DEL>.

 - Macro: int VWERASE
     This is the subscript for the WERASE character in the special
     control character array.  `TERMIOS.c_cc[VWERASE]' holds the
     character itself.

     The WERASE character is recognized only in canonical mode.  It
     erases an entire word of prior input, and any whitespace after it;
     whitespace characters before the word are not erased.

     The definition of a "word" depends on the setting of the
     `ALTWERASE' mode; Note: Local Modes.

     If the `ALTWERASE' mode is not set, a word is defined as a sequence
     of any characters except space or tab.

     If the `ALTWERASE' mode is set, a word is defined as a sequence of
     characters containing only letters, numbers, and underscores,
     optionally followed by one character that is not a letter, number,
     or underscore.

     The WERASE character is usually `C-w'.

     This is a BSD extension.

 - Macro: int VKILL
     This is the subscript for the KILL character in the special control
     character array.  `TERMIOS.c_cc[VKILL]' holds the character itself.

     The KILL character is recognized only in canonical input mode.
     When the user types the kill character, the entire contents of the
     current line of input are discarded.  The kill character itself is
     discarded too.

     The KILL character is usually `C-u'.

 - Macro: int VREPRINT
     This is the subscript for the REPRINT character in the special
     control character array.  `TERMIOS.c_cc[VREPRINT]' holds the
     character itself.

     The REPRINT character is recognized only in canonical mode.  It
     reprints the current input line.  If some asynchronous output has
     come while you are typing, this lets you see the line you are
     typing clearly again.

     The REPRINT character is usually `C-r'.

     This is a BSD extension.


automatically generated by info2www version 1.2.2.9