GNU Info
(emacs)Rectangles
Rectangles
==========
The rectangle commands operate on rectangular areas of the text: all
the characters between a certain pair of columns, in a certain range of
lines. Commands are provided to kill rectangles, yank killed
rectangles, clear them out, fill them with blanks or text, or delete
them. Rectangle commands are useful with text in multicolumn formats,
and for changing text into or out of such formats.
When you must specify a rectangle for a command to work on, you do it
by putting the mark at one corner and point at the opposite corner. The
rectangle thus specified is called the "region-rectangle" because you
control it in much the same way as the region is controlled. But
remember that a given combination of point and mark values can be
interpreted either as a region or as a rectangle, depending on the
command that uses them.
If point and the mark are in the same column, the rectangle they
delimit is empty. If they are in the same line, the rectangle is one
line high. This asymmetry between lines and columns comes about
because point (and likewise the mark) is between two columns, but within
a line.
`C-x r k'
Kill the text of the region-rectangle, saving its contents as the
"last killed rectangle" (`kill-rectangle').
`C-x r d'
Delete the text of the region-rectangle (`delete-rectangle').
`C-x r y'
Yank the last killed rectangle with its upper left corner at point
(`yank-rectangle').
`C-x r o'
Insert blank space to fill the space of the region-rectangle
(`open-rectangle'). This pushes the previous contents of the
region-rectangle rightward.
`M-x clear-rectangle'
Clear the region-rectangle by replacing its contents with spaces.
`M-x delete-whitespace-rectangle'
Delete whitespace in each of the lines on the specified rectangle,
starting from the left edge column of the rectangle.
`C-x r t STRING <RET>'
Replace rectangle contents with STRING on each line.
(`string-rectangle').
`M-x string-insert-rectangle <RET> STRING <RET>'
Insert STRING on each line of the rectangle.
The rectangle operations fall into two classes: commands for
deleting and inserting rectangles, and commands for blank rectangles.
There are two ways to get rid of the text in a rectangle: you can
discard the text (delete it) or save it as the "last killed" rectangle.
The commands for these two ways are `C-x r d' (`delete-rectangle') and
`C-x r k' (`kill-rectangle'). In either case, the portion of each line
that falls inside the rectangle's boundaries is deleted, causing any
following text on the line to move left into the gap.
Note that "killing" a rectangle is not killing in the usual sense;
the rectangle is not stored in the kill ring, but in a special place
that can only record the most recent rectangle killed. This is because
yanking a rectangle is so different from yanking linear text that
different yank commands have to be used and yank-popping is hard to
make sense of.
To yank the last killed rectangle, type `C-x r y'
(`yank-rectangle'). Yanking a rectangle is the opposite of killing
one. Point specifies where to put the rectangle's upper left corner.
The rectangle's first line is inserted there, the rectangle's second
line is inserted at the same horizontal position, but one line
vertically down, and so on. The number of lines affected is determined
by the height of the saved rectangle.
You can convert single-column lists into double-column lists using
rectangle killing and yanking; kill the second half of the list as a
rectangle and then yank it beside the first line of the list. Note:
Two-Column, for another way to edit multi-column text.
You can also copy rectangles into and out of registers with `C-x r r
R' and `C-x r i R'. Note: Rectangle Registers.
There are two commands you can use for making blank rectangles: `M-x
clear-rectangle' which blanks out existing text, and `C-x r o'
(`open-rectangle') which inserts a blank rectangle. Clearing a
rectangle is equivalent to deleting it and then inserting a blank
rectangle of the same size.
The command `M-x delete-whitespace-rectangle' deletes horizontal
whitespace starting from a particular column. This applies to each of
the lines in the rectangle, and the column is specified by the left
edge of the rectangle. The right edge of the rectangle does not make
any difference to this command.
The command `C-x r t' (`string-rectangle') replaces the contents of
a region-rectangle with a string on each line. The string's width need
not be the same as the width of the rectangle. If the string's width
is less, the text after the rectangle shifts left; if the string is
wider than the rectangle, the text after the rectangle shifts right.
The command `M-x string-insert-rectangle' is similar to
`string-rectangle', but inserts the string on each line, shifting the
original text to the right.
automatically generated by info2www version 1.2.2.9